Description
The Griffin Armorers wrench is a 4140 steel wrench hardened to 48RC. Black oxide and oil dipped. Some finish irregularity is common to this industrial tool. The wrench allows installation of Griffin Muzzle devices, Castle nuts on AR firearms, Griffin Low Pro Rigidâ?¢ rails, and interfaces with many Griffin Silencers for maintenance or configuring. This tool allows easy access to your favorite bottled beverage.
4140 Steel hardened to 48RC
Black oxide / oil dip finish
1/2″ drive compatible
5/8″ and 3/4″ open end wrenches
3 prong CAR wrench geometry
Bottle opener
Chris Franklin –
Can’t count how many times this tool has came in handy on the range and in the garage. The thin profile is great for installing muzzle devices and castle nuts. BONUS POINTS for the adult beverage opener!!!!
Freddie Brock –
This tool works as expected. Good quality. Would recommend to anyone installing these mounts.
David Britts –
What can I say, it works perfectly with my griffin minimal muzzle brakes.
Defense Materials Co.,LLC (verified owner) –
It’s a must have tool!
Brent –
Awesome tool, you’ll need it to torque all the Griffin muzzle devices Down, not to mention it has a bottle opener so you can enjoy a tasty beverage while doing it
Paul B. –
Great Wrench! I bought it for my taper mount flash hiders, I like it better than you general wrench because of the way smaller size to not make it real awkward when tightening your muzzle device. Thanks Griffin!
S.M. –
I recommend this wrench to all
M. Humphrey –
I needed something to install a muzzle device to be used with a suppressor. I had a number of tools for installing the muzzle device, but none to which I could both attach a torque wrench, and that also didn’t have pins or some other obstruction that would get in the way. This tool was perfect for the task.
Rob –
It gets the job done for a low price.
Dave –
Purchased for Dead Air Sandman muzzle installation. Needed wrench to be thin enough to work with spacer washers. . Works great. Good quality. .
David Dutton –
I appreciated the quick shipping. I found this wrench to be excellent in the instillation of my 30SD Flash Comp, and two M4SD Hammer Comps. The wrench fit snugly on the flats of all three devices as well as my torque wrench, and made easy work of installing all three new muzzle devices. I could not be more pleased.
AJ –
Good value.
Anonymous –
I bought this to install a surefire muzzle device. Surefire has their wrench adapted but it’s been sold out for a long time and a crowfoot is too wide for the wrench slots on the device. Griffins tool had the right size wrench opening and give how narrow it was, it fit on the slots with ease. I haven’t used it for it’s other features and functionality but at this price I’m fine with that. Most wrench’s are well over $50.
Iowa –
Good fitment on gun parts. Needed this to get between shims and muzzle brake. Can’t beat the price for this tool.
Anthony –
Was looking for tool to tighten and time the Dead Air Keymo Muzzle Brake to an MPX-K ILWT threaded barrel in conjunction with my Torque Wrench 1/2″ Drive. Worked out amazingly. Excellent craftsmanship and multipurpose. Very satisfied!
Granville –
Cost effective efficient solution.
Stephan Greenwood –
Wrench worked awesome and is thin to work muzzle devices and spacers. The tool is a little rough manufacturing only reason i didnt give it 5 stars
Charles Carlisle Jr –
Great product and even better price point! Fast shipping as well.
William –
This is a quality tool. Especially considering the price. Griffin also goes the extra mile and packages it nicely. You can tell when a company takes some pride in their work and it shows in this tool.
Trevor –
Irritated that I had to buy a third armorers wrench, I was looking to find an inexpensive wrench for timing my muzzle break. I needed a thin wrench and this one met my needs. It’s quality made and the right price. Thanks guys.
K –
Got this wrench for tightening a flash hider onto a jam nut for a PTR-32. Almost no shoulder on the barrel threads required a jam nut. This wrench was thin enough to fit on the flash hider only without interfering with the jam nut.
Robert Henry –
Worked very well for installing and removing A2 adapter for 1.375×24 suppressors